Loading...
Scan standard prints (3×5, 4×6, 5×7) at 600 DPI, small or detailed prints at 1200 DPI, in full color, saved as PNG or TIFF, with scanner auto-enhance turned off. Restoration quality is capped by scan quality: the AI rebuilds your photo from the pixels in the scan, and it cannot invent detail the scan never captured.
Every restoration decision an AI model makes is anchored to real pixels. A sharp 600 DPI scan gives the model eyelid creases, fabric weave, and film grain to work from. A soft 150 DPI scan forces the model to guess — and guessed detail is where waxy faces and invented textures come from. This guide gives you the exact settings, the mistakes that quietly ruin scans, and the cleaning step most people skip.
The settings that matter
| Setting | Use this | Why |
|---|---|---|
| Resolution | 600 DPI for standard prints; 1200 DPI for wallet-size, small, or very fine detail | 600 DPI captures all useful detail in a typical print; smaller prints enlarge the same detail onto less film, so they need more DPI |
| Color mode | Color (24-bit RGB), even for black-and-white prints | Sepia stains, yellowing, and damage marks are color data the white balance engine needs |
| File format | PNG or TIFF | JPEG compression smears exactly the fine grain the restoration relies on |
| Auto-enhance / Digital ICE | Off | Scanner "enhancement" blurs grain and invents sharpening halos before the AI ever sees the photo |
| Orientation | Photo flat, straight, glass-side down | Skewed scans cost you resolution and create correction artifacts |
| Cleanliness | Glass and print wiped with a dry microfiber cloth | Every dust speck becomes a spot the repair engine may treat as damage |
A note on DPI arithmetic: a 4×6 inch print scanned at 600 DPI produces 2400×3600 pixels. That is enough resolution to reprint at 8×12 inches after restoration, and it captures essentially everything a color print from the 1950s–1990s contains. Scanning at 2400 DPI makes files six times larger without adding real detail — the print's own grain is the ceiling, not the scanner. For small prints, though, the calculus flips: a wallet-size photo holds the same face in a fraction of the area, so 1200 DPI is the floor, not a luxury.
If you plan to enlarge a restored photo for reprinting, scan well now and read the upscaling guide — upscaling amplifies good scans and magnifies bad ones.
Cleaning the photo before scanning
Ten seconds of cleaning fixes more restorations than any setting:
- Blow or brush loose dust off the print — hold it vertically and let gravity take the debris, or use a soft photographic brush.
- Wipe gently with a dry microfiber cloth in one direction, not circles. This lifts fingerprints and surface grime.
- Never use water, alcohol, or cleaning sprays on old photographic prints. Water reactivates emulsion; solvents strip it. Dry methods only.
- Clean the scanner glass the same way, then re-check with the lid open under a light — glass dust scans as sharp speckles that read as damage.
- If a print is moldy or gritty, isolate it from your other photos, wipe it separately, and clean the glass afterward. Light surface mold restores well after cleaning; see the mold damage page for what to expect.
Phone camera vs flatbed scanner
A flatbed scanner is the right tool and costs little secondhand. But a modern phone works if you follow the rules that matter:
- Even, indirect light — a window on an overcast day beats any lamp. Direct light creates glare hotspots that read as damage.
- Shoot straight down, not at an angle: perspective skew distorts faces and makes later color work harder.
- Get close and tap to focus on the face; the phone must lock focus on the print, not the table.
- Turn off HDR and beauty filters — HDR blends exposures and smears grain; "enhancement" modes invent detail.
- Use the phone's RAW or highest-quality mode if available, and avoid cropping before upload.
A good phone capture restores better than a lazy scan. A flatbed at the settings in the table above restores better than both. If your goal is digitizing a whole collection rather than restoring a few prints, the digitizing guide compares scanners, apps, and services — and the batch restoration guide shows how to run stacks of scanned photos through restoration in one sitting.
The mistakes that quietly ruin scans
These cause most failed restorations, and none of them look like a problem in the scan itself:
- Saving as JPEG. JPEG's compression targets exactly the high-frequency grain a restoration needs. If your scanner only outputs JPEG, rescan — don't convert an existing JPEG, the loss is already baked in.
- Scanner auto-enhance. "Restoring" modes, unsharp masks, and Digital ICE each preprocess the photo before the AI sees it, and each one destroys real signal.
- Cropping tight in the scanner software. Leave a margin. The restoration engines use surrounding context to repair edges, and tight crops force them to guess at the frame.
- Grayscale mode for B&W prints. The yellow cast in an old "black-and-white" print is the color cast white balance removes. Grayscale scans throw that data away and often can't be fully corrected.
- Rescanning screenshots of scans. Every re-save through a messaging app compresses again. Move the original file, not a copy of a copy.
If a scan still produces strange results — waxy faces, blocky textures — it's almost always one of the mistakes above. The troubleshooting guide has a symptom table that names the cause and the fix. And if you're starting from zero, the getting started guide walks the whole path from upload to first restoration.
FAQ
What DPI should I scan old photos for restoration?
600 DPI for standard 3×5 to 8×10 prints, 1200 DPI for wallet-size or small photos, and 1200+ only for tiny or extremely fine sources like stamps or 35mm negatives. Higher DPI makes bigger files without adding real detail — the print's grain is the limit, not the scanner.
Should I scan photos as JPEG or TIFF or PNG?
TIFF or PNG. JPEG compression discards fine grain before restoration even starts, and that grain is what keeps faces natural. Scan once, losslessly, and archive that file — every future restoration works from it without new loss.
Can I scan black-and-white photos in color mode?
Yes — do. Color mode captures the sepia and yellow casts that white balance engines are designed to remove, and it records damage stains at full fidelity. Grayscale scans permanently discard that information and usually restore worse.
Is a phone photo good enough for AI restoration?
For prints in good condition, yes, if you shoot straight down in even light with HDR and filters off, focused on the face. A flatbed at 600 DPI still wins for damaged prints, small photos, and anything you plan to reprint large. Damaged prints especially benefit from the scanner glass flattening curls and bubbles.
Do I need to clean old photos before scanning?
Yes — it's the highest-value ten seconds in the whole workflow. Dry microfiber on the print, dry microfiber on the glass, never any liquid. Dust specks scan as sharp spots that the repair engine must treat as damage, and they dull the final result.
Scan well, restore once
Set 600 DPI, color mode, PNG, auto-enhance off — then let the restoration do its work. Restore a photo from your scan — the first one is free.
